| Table of Contents | ||
|---|---|---|
|
Introduction
...
This article describes how to configure a Trainings Place exercise station with and or without a training device to perform a training in Rehab. A trainings place without training device with guard, serves purely for ECG monitoring and is referred to as A exercise station with custo guard but without a training device serves purely ECG for monitoring and is preferred used for telemetry.
Configuration
...
Exercise Station for Trainings with Training
...
Device
Pre-Conditions
...
- Be sure that you have the necessary License Options, see https://www.customed.de/docs/x/DQK
...
- Make the Basic Settings
...
- of the Training Device (Treadmill or Ergometer) in custo diagnostic, see https://www.customed.de/docs/x/4gC
...
- Make the
...
- custo com RF Connection Settings, see https://www.customed.de/docs/x/IgK
Configuration sequence
...
Preparation
Enter the Settings Page "Device Connection" with Steps 1-3
...
Select the Number of Exercise Stations
Hint: If you want to use more than 8 exercise stations
...
if there are more than 8 places, 2 Monitors must be used.
next Step, set 
Select "Type of exercises"
The most common setting is "Free exercies with Smart-Cards". It means that the patient selection takes place individually via the context menu on the Trainings Place Exercise Station main page.
"With smart card" means: if the ergometer has a chip smart card reader, the selection of the patient takes place by inserting the smart Cardcard into the ergometer.
A detailed description of the types of exercise is you can find here: https://www.customed.de/docs/x/H4CU.
next Step
Selection of Trainingsplaces
Configure the Exercise Station
Preparations
Each exercise station must be configured individually. To configure an exercise station you have to select the apropriate exercise station.Each training place must be configured separately.
By click on the arrow button see arrow, it is its possible to change from place station to placestation.
Starting is always from No. 1 and extends goes up to the maximum set number, see Configuration Trainingsplace up to custo diagnostic
next Step
Assigning the Training Device with Equipment blood pressure, SPO2 and ECG amplifier from an ergometer to a training place
Selection of the ergometer
...
of exercise stations.
Select the Training Device
Here you hate to assign a training device with integrated equipment like blood pressure measuring device, SpO2 sensor or and ECG amplifier to a exercise station.
- Click "Exercise device" in the list "Device list of exercise station"
- Select an exercise device (eg. Ergometer or Treadmill) from the list "Exercise devices"
...
...
- also)
- If the training device has integrated options eg. chip card reader (smart card) or suction system (ECG device) you can enable or disable here these options.
Select an ECG Device
If the training device have an integrated ECG device you can add here the ECG device to the exercise station.
- Click "ECG" in the list "Device list of exercise station"
- Select the apropriate device from the list "ECG device"
Select the SpO2 Device
- Click "SpO2" in the list "Device list of exercise station"
- Select a device from the list "SpO2 device"
Blood Pressure
If you use a training device with integrated blood pressure measuring device no action is here required.
If you want to use an external blood pressure measuring device (eg. Metronik BL-6, for example in combination with a treadmill) you have to configure this device here.
- Click "BP" in the list "Device list of exercise station"
- Select a device from the list "Blood pressure measuring device"
...
ecg:
1: Click "ECG" and 2: select "Exercice Device" and Click "Save"
SpO2:
1: Click "SPO2" and 2: select "Exercice Device" and Click "Save"
Blood Pressure:
does not have to be set, values are transferred automatically via the protocol
Assigning the Training Device with guard
Configuration comRF
Install Driver:
Variante 1
via Setup Selection, see
or Setup Command Line Parameters
Settings for comRF
Connect comRF to USB Port, and than configure the 1:1 Connection comRF to guard (as an Example, for 2 Trainingsplaces are needed 3 comRF Sticks)
...
first Step
All necessary COMRF sticks are listed? f not, check the comRF Installation, see https://www.customed.de/docs/x/IgK, if yes, continue with the next step
Assigning guard
1: Click "ECG", 2: select "guard" and 3: Click "Save"
for fix Connection on the Trainingsplace:
Introduction: For a fast and effective work it is better to fix every single guard with a fixed training place.
The guards are sorted by the serial numbers and the lowest is assigned to training place 1 and for example the highest one to training place 16.
Assigning to guardAnchor Assigning to guard Assigning to guard
| Assigning to guard | |
| Assigning to guard |
next Step:
First, each guard is labeled with the training place number. This number makes it easier to assign to the training site later.
Click "custo guard labeling"
1: Click "Sort" means: it is sorted from the lowest to the highest serial number, 2: Enter the training place numbers 3: Click "Save"
next Step: fixed assignment of the guard to the training place
1: activation the Setting "Allocate as fixed", 2 Enter "custo guard allocation"
1: Button to select the found guards, here in the example the guard with the number 1 to training place 1.
...
Assigning guard
for fix Connection on the Trainingsplace:
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
...
Telemetry
Conditions:
Telemetry means: There is only
...
ECG recording without training
...
device control instead.
Trainingsplace without Trainings Device
...
1: Click "Selection Exercise" 2: select "No device" and Click "Save"
for Setting guard see Chapter Assigning to
...