View Source

Important: the Lode ergometers and treadmills with blood pressure do need an external trigger, this option includes the license and the cable:

12149/LODE Real time QRS-Trigger-Modul incl. Trigger cable for LODE ergometers with blood pressure.

From version 4.6.15 and 5.3.1. we have changed the behavior from custo diagnostic in case a blood pressure with a warning and/or an error have been sent by the lode ergometer.

This changes do support Lode ergometers with the following firmware versions and above.

CIM (Communication Interface Module) Firmware 1.0.27 or above,

KIM (Kadenz Interface Module) Firmware 1.0.5 or above

UIM70 (User Interface Module) Firmware 1.0.30 or above

ECM (Ergometer Control Module) Firmware 1.0.6 or above

In the past the behavior was as follows, in case a warning for a blood pressure was sent by the Lode ergometer custo diagnostic handled it in the same way as an error.

An error (7-510) was displayed in custo diagnostic when the ergometer sent warning for the measured blood pressure value. This has been done because custo diagnostic does not receive any information about the warning.

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-0-0.png

After many complains, because the Lode ergometer does show the blood pressure although the was a warning, custo med decided to, also display the blood pressure values sent by the ergometer with a warning.

(In case of a warning you should think about, arm movement, to less Korotkow sound and so on)

custo diagnostic setup

In custo the following settings should be made. Set the trigger port

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_14-52-55.png

For the ergometer the following settings should be made,

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-12-46.png

BP data, Without BP Status and disable watchdog should be selected.

How to make the setting can also be seen in the following VIDEO

Choose in Ergospiro and or Stress ECG that the blood pressure device is in the ergometer,

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-24-38.png

Lode ergometer setup

In the ergometer the following setting should be made under Terminal settings,

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-14-41.png

Communication Protocol Lode 38K4

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-15-39.png

Baud rate must be set to 38400,

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-16-33.png

Value 999 on BPM should be selected,

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-17-3.png

The correct communication port should be selected,

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-18-8.png

After that we activated Terminal or select the mode to start with Terminal

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-19-17.png

Select default start menu

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-19-50.png

Choose terminal

Hardware > Lode ergometer with Blood pressure from 4.6.15 and 5.3.1 > image2020-6-23_15-20-26.png

Safe by pressing the right arrow and restart the device.